16. Marking and Packaging
16.1
Marking: 16.1.1 Identification—Unless otherwise specified, each plate, sheet, and strip shall be marked in the respective location indicated below, with the number of this specification, heat number, manufacturer’s identification, and the nominal thickness in inches. The characters shall be not less than 3/8 in.(9.52 mm)in height, shall be applied using a suitable marking fluid, and shall be capable of being removed with a hot alkaline cleaning solution without rubbing. The marking shall have no deleterious effect on the material or its performance. The characters shall be sufficiently stable to withstand ordinary handling.
TABLE 7 Permissible Variations in Width A of Titanium Strip
|
Specified Thickness, in.(mm) |
Permissible Variations in Thickness, plus and minus, for Widths Given, in.(mm) |
||
|
Under 1/2 to 3/16(12.70 to 4.76),incl |
1/2 to 6(12.70 to 152.40),incl |
Over 6 to 9(152.40 to 228.60),incl |
|
| Under 3/16 to 0.161(4.76 to 4.09),incl |
… |
0.016(0.41) |
0.020(0.51) |
| 0.160 to 0.100(4.06 to 2.54),incl |
0.010(0.25) |
0.010(0.25) |
0.016(0.41) |
| 0.099 to 0.069(2.51 to 1.75),incl |
0.008(0.20) |
0.008(0.20) |
0.010(0.25) |
| 0.068(1.73) and under |
0.005(0.13) |
0.005(0.13) |
0.005(0.13) |
|
Specified Thickness, in.(mm) |
Permissible Variations in Thickness, plus and minus, for Widths Given, in.(mm) |
||
|
Over 9 to 12(228.60 to 304.80),incl |
Over 12 to 20(304.80 to 508.0),incl |
Over 20 to 24(508.0 to 609.6),excl |
|
| Under 3/16 to 0.161(4.76 to 4.09),incl |
0.020(0.51) |
0.031(0.79) |
0.031(0.79) |
| 0.160 to 0.100(4.06 to 2.54),incl |
0.016(0.41) |
0.020(0.51) |
0.020(0.51) |
| 0.099 to 0.069(2.51 to 1.75),incl |
0.010(0.25) |
0.016(0.41) |
0.020(0.51) |
| 0.068(1.73) and under |
0.010(0.25) |
0.016(0.41) |
0.020(0.51) |
TABLE 8 Permissible Variations in Length of Titanium Strip
|
Specified Length,ft(m) |
Permissible Variations in length,in.(mm) |
|
To 5(1.524), incl |
+3/8(+9.52),-0 |
|
Over 5 to 10(1.524 to 3.048), incl |
+1/2(+12.70),-0 |
|
Over 10 to 20(3.048 to 6.096), incl |
+5/8(+15.88),-0 |
TABLE 9 Permissible Variations in Thickness of Titanium StripA
|
Specified Thickness, in.(mm) |
Permissible Variations in Thickness, plus and minus,for Widths Given, in.(mm) |
|||
|
Under 1 to 3/16(25.4 to 4.76),incl |
Under 3 to 1(76.2 to 25.4),incl |
3 to 6(76.2 to 152.4),incl |
Over 6 to 9(152.4 to 228.6),incl |
|
|
Under 3/16 to 0.161(4.76 to 4.09),incl |
0.002(0.05) |
0.002(0.05) |
0.004(0.10) |
0.004(0.10) |
|
0.160 to 0.100(4.06 to 2.54),incl |
0.002(0.05) |
0.002(0.05) |
0.003(0.08) |
0.004(0.10) |
|
0.099 to 0.069(2.51 to 1.75),incl |
0.002(0.05) |
0.002(0.05) |
0.003(0.08) |
0.003(0.08) |
|
0.068 to 0.050(1.73 to 1.27),incl |
0.002(0.05) |
0.002(0.05) |
0.0025(0.06) |
0.003(0.08) |
|
0.049 to 0.040(1.24 to 1.02),incl |
0.002(0.05) |
0.002(0.05) |
0.0025(0.06) |
0.003(0.08) |
|
0.039 to 0.035(0.99 to 0.89),incl |
0.0015(0.04) |
0.0015(0.04) |
0.002(0.05) |
0.003(0.08) |
|
0.034 to 0.029(0.86 to 0.74),incl |
0.001(0.03) |
0.0015(0.04) |
0.0015(0.04) |
0.0025(0.06) |
|
0.028 to 0.026(0.71 to 0.66),incl |
0.001(0.03) |
0.001(0.03) |
0.0015(0.04) |
0.002(0.05) |
|
0.025 to 0.020(0.64 to 0.51),incl |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
0.002(0.05) |
|
0.019 to 0.017(0.48 to 0.43),incl |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
0.0015(0.04) |
|
0.016 to 0.013(0.41 to 0.33),incl |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
0.0015(0.04) |
|
0.02(0.30) |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
|
0.011(0.28) |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
|
0.010B(0.25) |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
0.001(0.03) |
|
Specified Thickness, in.(mm) |
Permissible Variations in Thickness, plus and minus,for Widths Given, in.(mm) |
|||
|
Over 9 to 12(228.6 to 304.8),incl |
Over 12 to 16(304.8 to 406.4),incl |
Over 16 to 20(406.4 to 508.0),incl |
Over 20 to 24(508.0 to 609.6),incl |
|
| Under 3/16 to 0.161(4.76 to 4.09),incl |
0.004(0.10) |
0.005(0.13) |
0.006(0.16) |
0.006(0.16) |
| 0.160 to 0.100(4.06 to 2.54),incl |
0.004(0.10) |
0.004(0.10) |
0.005(0.13) |
0.005(0.13) |
| 0.099 to 0.069(2.51 to 1.75),incl |
0.003(0.08) |
0.004(0.10) |
0.004(0.10) |
0.004(0.10) |
|
0.068 to 0.050(1.73 to 1.27),incl |
0.003(0.08) |
0.003(0.08) |
0.004(0.10) |
0.004(0.10) |
|
0.049 to 0.040(1.24 to 1.02),incl |
0.003(0.08) |
0.003(0.08) |
0.004(0.10) |
0.004(0.10) |
|
0.039 to 0.035(0.99 to 0.89),incl |
0.003(0.08) |
0.003(0.08) |
0.003(0.08) |
0.003(0.08) |
|
0.034 to 0.029(0.86 to 0.74),incl |
0.0025(0.06) |
0.0025(0.06) |
0.003(0.08) |
0.003(0.08) |
|
0.028 to 0.026(0.71 to 0.66),incl |
0.002(0.05) |
0.002(0.05) |
0.0025(0.06) |
0.003(0.08) |
|
0.025 to 0.020(0.64 to 0.51),incl |
0.002(0.05) |
0.002(0.05) |
0.0025(0.06) |
0.0025(0.06) |
|
0.019 to 0.017(0.48 to 0.43),incl |
0.0015(0.04) |
0.002(0.05) |
0.002(0.05) |
0.002(0.05) |
|
0.016 to 0.013(0.41 to 0.33),incl |
0.0015(0.04) |
0.0015(0.04) |
0.002(0.05) |
0.002(0.05) |
|
0.02(0.30) |
0.001(0.03) |
0.0015(0.04) |
0.0015(0.04) |
0.0015(0.04) |
|
0.011(0.28) |
0.001(0.03) |
0.0015(0.04) |
0.0015(0.04) |
0.0015(0.04) |
|
0.010B(0.25) |
0.001(0.03) |
0.0015(0.04) |
0.0015(0.04) |
|
TABLE 10 Permissible Variations in Weight of Titanium Strip
| The actual shipping weight of any one item of an ordered thickness and width |
| In any finish may exceed estimated weight by as much as 10% |
16.1.2 Plate, flat sheet, and flat strip over 6 in.(152 mm) in width shall be marked in lengthwise rows of characters recurring at intervals not greater than 3 in.(76 mm), the rows being spaced not more than 2 in.(51 mm) apart and alternately staggered. Heat numbers shall occur at least 3 times across the width of the sheet and at intervals not greater than 2 ft(0.610 m)along the length. As an option, when permitted, each plate, sheet, or cut length strip may be marked in at least one corner with the number of this specification, heat number, manufacturer’s identification, and the nominal thickness in inches or millimeters as required.
16.1.3 Flat strip 6 in.(152 mm) and under in width shall be marked near one end. 16.1.4 Coiled sheet and strip shall be marked near the outside end of the coil. 16.2 Packaging—Unless otherwise specified, material purchased under this specification may be packaged for shipment either by boxing, crating, single boarding, burlapping, or with no protection in accordance with the manufacturer’s standard practice.
TABLE 11 Permissible Variations in Width and Length A of
Titanium Plate, Rectangular, Sheared
|
Specified Length, in. (mm) |
Specified Width, in.(mm) |
Permissible Variations Over Specified Dimension fir Thickness Given, in.(mm) |
||
|
Under 3/8(9.52) |
3/8 to 5/8(9.52 to 15.88),excl |
|||
|
Width |
Length |
Width |
||
|
Under 120(3048) |
Under 60(1524) |
3/8(9.52) |
1/2(12.70) |
7/16(11.11) |
|
60 to 84(1524 to 2134),excl |
7/16(11.11) |
5/8(15.88) |
1/2(12.70) |
|
|
84 to 108(2134 to 2743),excl |
1/2(12.70) |
3/4(19.05) |
5/8(15.88) |
|
|
108(2743) or over |
5/8(15.88) |
7/8(22.22) |
3/4(19.05) |
|
|
120 to 240(3048 to 6096),excl |
Under 60(1524) |
3/8(9.52) |
3/4(19.05) |
1/2(12.70) |
|
60 to 84(1524 to 2134),excl |
1/2(12.70) |
3/4(19.05) |
5/8(15.88) |
|
|
84 to 108(2134 to 2743),excl |
9/16(14.29) |
7/8(22.22) |
11/16(17.46) |
|
|
108(2743) or over |
5/8(15.88) |
1 (25.40) |
3/4(19.05) |
|
|
240 to 360(6096 to 9144),excl |
Under 60(1524) |
3/8(9.52) |
1 (25.40) |
1/2(12.70) |
|
60 to 84(1524 to 2134),excl |
1/2(12.70) |
1 (25.40) |
5/8(15.88) |
|
|
84 to 108(2134 to 2743),excl |
9/16(14.29) |
1 (25.40) |
11/16(17.46) |
|
|
108(2743) or over |
11/16(17.46) |
11/8(28.58) |
7/8(22.22) |
|
|
360 to 480(9144 to 7112),excl |
Under 60(1524) |
7/16(11.11) |
11/8(28.58) |
1/2(12.70) |
|
60 to 84(1524 to 2134),excl |
1/2(12.70) |
11/4(31.75) |
5/8(15.88) |
|
|
84 to 108(2134 to 2743),excl |
9/16(14.29) |
11/4(31.75) |
3/4(19.05) |
|
|
108(2743) or over |
3/4(19.05) |
13/8(34.92) |
7/8(22.22) |
|
|
480 to 600(7112 to 15 240),excl |
Under 60(1524) |
7/16(11.11) |
11/4(31.75) |
1/2(12.70) |
|
60 to 84(1524 to 2134),excl |
1/2(12.70) |
13/8(34.92) |
5/8(15.88) |
|
|
84 to 108(2134 to 2743),excl |
5/8(15.88) |
13/8(34.92) |
3/4(19.05) |
|
|
108(2743) or over |
3/4(19.05) |
11/2(38.10) |
7/8(22.22) |
|
|
600(15 240) or over |
Under 60(1524) |
1/2(12.70) |
13/4(44.45) |
5/8(15.88) |
|
60 to 84(1524 to 2134),excl |
5/8(15.88) |
13/4(44.45) |
3/4(19.05) |
|
|
84 to 108(2134 to 2743),excl |
5/8(15.88) |
13/4(44.45) |
3/4(19.05) |
|
|
108(2743) or over |
7/8(22.22) |
13/4(44.45) |
1 (25.40) |
|
|
Specified Length, in. (mm) |
Specified Width, in.(mm) |
Permissible Variations Over Specified Dimension fir Thickness Given, in.(mm) |
||
|
3/8 to 5/8(9.52 to 15.88),excl |
5/8(15.88) and over |
|||
|
Width |
Width |
Length |
||
|
Under 120(3048) |
Under 60(1524) |
5/8(15.88) |
11/2(12.70) |
3/4(19.05) |
|
60 to 84(1524 to 2134),excl |
11/16(17.46) |
5/8(17.46) |
7/8(22.22) |
|
|
84 to 108(2134 to 2743),excl |
7/8(22.22) |
3/4(19.05) |
1 (25.40) |
|
|
108(2743) or over |
1 (25.40) |
7/8(22.22) |
11/8(28.58) |
|
|
120 to 240(3048 to 6096),excl |
Under 60(1524) |
7/8(22.22) |
5/8(15.88) |
1 (25.40) |
|
60 to 84(1524 to 2134),excl |
7/8(22.22) |
3/4(19.05) |
1 (25.40) |
|
|
84 to 108(2134 to 2743),excl |
15/16(23.81) |
13/16(20.64) |
11/8(28.58) |
|
|
108(2743) or over |
11/8(28.58) |
7/8(22.22) |
11/4(31.75) |
|
|
240 to 360(6096 to 9144),excl |
Under 60(1524) |
11/8(28.58) |
5/8(15.88) |
11/4(31.75) |
|
60 to 84(1524 to 2134),excl |
11/8(28.58) |
3/4(19.05) |
11/4(31.75) |
|
|
84 to 108(2134 to 2743),excl |
11/8(28.58) |
7/8(22.22) |
13/8(34.92) |
|
|
108(2743) or over |
11/4(31.75) |
1 (25.40) |
13/8(34.92) |
|
|
360 to 480(9144 to 7112),excl |
Under 60(1524) |
11/4(31.75) |
5/8(15.88) |
11/2(38.10) |
|
60 to 84(1524 to 2134),excl |
1 3/8(34.92) |
3/4(19.05) |
11/2(38.10) |
|
|
84 to 108(2134 to 2743),excl |
1 3/8(34.92) |
7/8(22.22) |
11/2(38.10) |
|
|
108(2743) or over |
11/2(38.10) |
1 (25.40) |
15/8(41.28) |
|
|
480 to 600(7112 to 15 240),excl |
Under 60(1524) |
11/2(38.10) |
5/8(15.88) |
15/8(41.28) |
|
60 to 84(1524 to 2134),excl |
11/2(38.10) |
3/4(19.05) |
15/8(41.28) |
|
|
84 to 108(2134 to 2743),excl |
11/2(38.10) |
7/8(22.22) |
15/8(41.28) |
|
|
108(2743) or over |
15/8(41.28) |
1 (25.40) |
13/4(44.45) |
|
|
600(15 240) or over |
Under 60(1524) |
17/8(47.62) |
3/4(19.05) |
17/8（47.62） |
|
60 to 84(1524 to 2134),excl |
17/8(47.62) |
7/8(22.22) |
17/8（47.62） |
|
|
84 to 108(2134 to 2743),excl |
17/8(47.62) |
7/8(22.22) |
17/8（47.62） |
|
|
108(2743) or over |
2 (50.80) |
11/8(28.58) |
21/4(57.15) |
|
A The tolerance under the specified width length is 1/4 in.(6.35 mm)
TABLE 12 permissible Variations from a Flat Surface for
Titanium Plate, Annealed
Note 1—Variations in flatness apply to plates up to 15 ft (4.57 m) in length, or to any ft of longer plates.
Note 2—If the longer dimension is under 36 in.(914 mm) the variation is not greater than 1/4 in. (6.35 mm).
Note 3—The shorter dimension specified is considered the width and the variation in flatness across the width does not exceed the tabular amount for that dimension.
Note 4—The maximum deviation from a flat surface does not customarily exceed the tabular tolerance for the longer dimension specified.
| Specified Thickness, in.(mm) | 48(1219) or under | 48,excl to 60(1219 to 1524),excl | 60 to 72(1524 to 1829),excl | 72 to 84(1829 to 2134),excl | 84 to 96(2134 to 2743),excl |
| 3/16 to 1/4(4.76 to 6.35),excl | 3/4(19.05) | 11/16(26.99) | 11/4(31.75) | 13/8(34.92) | 15/8(41.28) |
| 1/4 to 3/8(6.35 to 9.54),excl | 11/16(17.46) | 3/4(19.05) | 15/16(23.81) | 11/8(28.58) | 13/8(34.92) |
| 3/8 to 1/2(9.54 to 12.70),excl | 1/2(12.70) | 9/16(14.29) | 11/16(17.46) | 3/4(19.05) | 15/16(23.81) |
| 1/2 to 3/4(12.70 to 19.05),excl | 1/2(12.70) | 9/16(14.29) | 5/8(15.88) | 5/8(15.88) | 13/16(20.64) |
| 3/4 to 1(19.05 to 25.40),excl | 1/2(12.70) | 9/16(14.29) | 5/8(15.88) | 5/8(15.88) | 3/4(19.05) |
| 1 to 11/2(25.40 to 38.10),excl | 1/2(12.70) | 9/16(14.29) | 9/16(14.29) | 9/16(14.29) | 11/16(17.46) |
| Over 11/2 to 4(38.10 to 101.6),excl | 3/16(4.76) | 5/16(7.94) | 3/8(9.54) | 7/16(11.11) | 1/2(12.70) |
| Over 4 to 6(101.6 to 152.4),excl | 1/4(6.35) | 3/8(9.54) | 1/2(12.70) | 9/16(14.29) | 5/8(15.88) |
| Specified Thickness, in.(mm) | 96 to 108(2438 to 2743),excl | 108 to 120(2743 to 3048),excl | 120 to 144(3048 to 3658),excl | 144(3658) and Over |
| 3/16 to 1/4(4.76 to 6.35),excl | 15/8(41.28) | … | … | … |
| 1/4 to 3/8(6.35 to 9.54),excl | 17/16(36.51) | 19/16(36.69) | 17/8(47.62) | … |
| 3/8 to 1/2(9.54 to 12.70),excl | 11/8(28.58) | 11/4(31.75) | 17/16(36.51) | 13/4(44.45) |
| 1/2 to 3/4(12.70 to 19.05),excl | 11/8(28.58) | 11/8(28.58) | 11/8(28.58) | 13/8(34.92) |
| 3/4 to 1(19.05 to 25.40),excl | 13/16(20.64) | 15/16(23.81) | 1 (25.40) | 11/8(28.58) |
| 1 to 11/2(25.40 to 38.10),excl | 11/16(17.46) | 11/16(17.46) | 3/4(19.05) | 1 (25.40) |
| Over 11/2 to 4(38.10 to 101.6),excl | 9/16(14.29) | 5/8(15.88) | 3/4(19.05) | 7/8(22.22) |
| Over 4 to 6(101.6 to 152.4),excl | 3/4(19.05) | 7/8(22.22) | 1 (25.40) | 11/8(28.58) |
17. Keywords 17.1 plate; sheet; strip; titanium; titanium alloys
TABLE 13 Permissible variation in Thickness for Titanium Plate
|
Specified Thickness, in.(mm) |
Width, in.(mm)A |
|||
|
To 84(2134),incl |
Over 84(2134) to 120(3048),incl |
Over 120(3048) to 144(3658),incl |
Over 144(3658) |
|
|
Tolerances Over Specified Thickness, in.(mm)B |
||||
|
0.1875 (4.76) to 0.375(9.52),excl |
0.045(1.14) |
0.050(1.27) |
… |
… |
|
0.375(9.52) to 0.750(19.05),excl |
0.055(1.40) |
0.060(1.52) |
0.075(1.90) |
0.090(2.29) |
|
0.750(19.05) to 1.000(25.40),excl |
0.060(1.52) 主站蜘蛛池模板： 崇明县| 华容县| 苏尼特右旗| 余庆县| 屯留县| 泸溪县| 行唐县| 溧阳市| 大厂| 石楼县| 淮北市| 林口县| 锡林浩特市| 枝江市| 佛坪县| 利辛县| 高尔夫| 平阴县| 江陵县| 弥渡县| 页游| 晋中市| 永德县| 都匀市| 景谷| 克拉玛依市| 九台市| 平山县| 龙里县| 宁晋县| 彭水| 微山县| SHOW| 民丰县| 淮滨县| 英吉沙县| 石首市| 三门峡市| 安国市| 石阡县| 云霄县| | |||